SEMIL-1700GC: IP67 Waterproof GPU Computer Including NVIDIA RTX 2000 Ada /L4 and Supporting Intel Xeon E /9th/8th-Gen Core CPU with All M12 Connectors
SEMIL-1700GC SeriesSEMIL-1700GC series is one of the world’s first IP67-rated, waterproof, and dustproof inference servers with pre-installed NVIDIA RTX 2000 Ada or L4 for the most demanding environments. It is a brand-new page in Neousys’ chapter of innovations as it represents a new level of robustness for rugged-edge AI solutions. Coupled with Intel Xeon E or 9th/ 8th-Gen Core CPU, the system delivers excellent CPU and GPU performances for advanced edge AI applications in various environmental settings. SEMIL-1700GC series features Neousys’ patented system architecture* to guarantee -40°C to 70°C fanless operation in a rack or wall-mountable 2U 19” enclosure.
- IP67 waterproof GPU computer with NVIDIA RTX 2000 Ada/ L4
- Intel Xeon E or 9th/8th-Gen Core i7/ i5/ i3 CPU
- Patented waterproof 2U 19” chassis for rack or wall-mount
- Up to eight 802.3at Gigabit PoE+ ports via M12 X-coded connectors
- VGA, USB 2.0, and COM ports via M12 A-coded connectors
- 8 to 48V wide-range DC input with built-in ignition power control
- MIL-STD-810G and EN 50155 EMC compliant
Frequently Asked Questions
All I/O on the SEMIL-1700GC Series uses waterproof M12 connectors. Depending on model, the system provides:
- 1x IEEE 802.3at Gigabit PoE+ port via Intel I219 plus 3 or 7x IEEE 802.3at Gigabit PoE+ ports via Intel I210 (M12 X-coded), for a total of 4 or 8 PoE+ ports
- 1x VGA port (M12 A-coded), supporting up to 1920x1200 resolution
- 2x or 4x USB 2.0 ports (M12 A-coded), plus 1 internal USB 2.0 port
- 2x 3-wire RS-232 COM ports, COM1 and COM2 (M12 A-coded)
- 1x mic-in/speaker-out audio port (M12 A-coded) on SEMIL-1728GC/1748GC models only
- An optional 10 GbE port via Intel X550AT (M12 X-coded), backward compatible with 5Gb, 2.5Gb, and GbE connections
The system accepts 8 to 48V DC input via an M12 S-coded connector. It has a built-in ignition power control feature that reads the IGN/GND signal via the M12 serial port connector, useful for in-vehicle installations. Supplying voltage over 48V will damage the system.
Maximum power consumption with the Intel Xeon E-2278GE CPU is approximately 188.88W at 24V or 192W at 48V (max TDP), and 148.08W at 24V or 150.24W at 48V when configured for 35W TDP.
With a 35W CPU, the system operates from -40°C to 70°C. With a CPU rated 65W or higher, it can run -40°C to 70°C when the CPU is configured in BIOS for 35W TDP mode, or -40°C to 50°C when configured for 65W TDP mode (thermal throttling may occur under sustained full load in this mode). Storage temperature is -40°C to 85°C, with humidity tolerance of 10% to 90% non-condensing.
The system is compliant with MIL-STD-810G for vibration (Method 514.6/514.7, Category 4) and shock (Method 516.6/516.7, Procedure I). EMC certifications include EN 50121 (EN 50155 EMC) and CE/FCC Class A per EN 55032 and EN 55035. Note that sub-zero operation requires a wide-temperature-rated HDD or SSD.
The system supports:
- 2x internal SATA ports for 2.5" HDD/SSD installation, supporting RAID 0/1
- 2x full-size mSATA ports (muxed with mini-PCIe)
- 1x M.2 2280 M-key socket (PCIe Gen3 x4) for NVMe SSD or Intel Optane memory
- 2x full-size mini PCI Express sockets (muxed with mSATA); SEMIL-17x8GC models add 2 additional full-size mini-PCIe sockets
- Up to 64GB of DDR4-2666/2400 SDRAM (ECC or non-ECC) across two SO-DIMM sockets
Neousys has tested the system with Microsoft Windows 10 (x64), Fedora 29, and Ubuntu 16.04.5 LTS / 18.04.0 LTS. For other Linux distributions, the kernel should be 4.15.18 or later. On Linux, users may need to manually compile and install drivers for the Intel graphics or I210 GbE controller if not already included in the kernel. Neousys also provides a Drivers & Utilities DVD that can automatically detect the Windows OS and install all necessary drivers.
The SEMIL-1700GC Series measures 440mm (W) x 310mm (D) x 90.5mm (H), excluding the rack-mount bracket. Weight is 12 kg for the SEMIL-1724GC/1744GC and 12.2 kg for the SEMIL-1728GC/1748GC. The system uses a patented 2U 19" chassis and supports both rack-mounting and wall-mounting.
The system has full-size mini-PCIe expansion slots (2 slots on all models, with 2 additional slots on SEMIL-17x8GC models). Off-the-shelf mini-PCIe modules can be installed to add features such as 5G/4G, WiFi, GPS, CAN bus, or an analog frame grabber. Note: if a wireless module is installed after purchase, the unit may need to be returned to Neousys or an authorized SEMIL distributor for SMA antenna installation to preserve the IP67 waterproof rating.
All four models share the same chassis, CPU options, and DC input, but differ in GPU and PoE+ port count:
- SEMIL-1724GC: NVIDIA RTX 2000 Ada, 4 total PoE+ ports (1x I219 + 3x I210), 2x USB 2.0, no audio port
- SEMIL-1728GC: NVIDIA RTX 2000 Ada, 8 total PoE+ ports (1x I219 + 7x I210), 4x USB 2.0, includes mic-in/speaker-out audio port
- SEMIL-1744GC: NVIDIA L4, 4 total PoE+ ports (1x I219 + 3x I210), 2x USB 2.0, no audio port
- SEMIL-1748GC: NVIDIA L4, 8 total PoE+ ports (1x I219 + 7x I210), 4x USB 2.0, includes mic-in/speaker-out audio port
All four are also offered in an optional -10G variant that adds a 10 GbE port via Intel X550AT.
How-to Guides
- Disconnect all cables and shut down the system.
- Turn the system upside-down and place it on a flat, sturdy surface.
- Unscrew the indicated screws in descending order and gently lift the bottom panel to access internal components.
- If hard drives are installed, disconnect the SATA/power connector by pulling on the connector body, not the cable.
- Locate the mini-PCIe slot(s) and corresponding SIM slot(s).
- If installing a 5G/4G module, slide and lift the SIM card holder, insert the SIM card with pins facing up, and secure the holder.
- Insert the mini-PCIe module into the slot at a 45-degree angle, press down, and secure it with a screw.
- Refer to the module's manual and connect the antenna as needed.
- For SMA antenna installation, the unit may need to be returned to an authorized Neousys/SEMIL distributor to preserve IP67 waterproofing.
- Ensure the O-ring is properly seated in the groove, tuck cables back into the enclosure, and close the bottom panel.
- Secure the panel screws at a torque range of 6.3-7.7 kgf-cm in ascending order.
- Disconnect all cables and shut down the system.
- Turn the system upside-down and place it on a flat, sturdy surface.
- Unscrew the indicated screws in descending order and gently lift the bottom panel.
- If replacing an existing drive, disconnect the SATA/power connector by pulling on the connector body, not the cable, then remove the screws on both sides of the drive.
- Place the new hard drive between the brackets and secure it with screws on both sides. Repeat if installing a second drive.
- Connect the SATA/power cable to the drive(s).
- Ensure the O-ring is properly seated in the groove, tuck cables into the enclosure, and close the bottom panel.
- Secure the panel screws at a torque range of 6.3-7.7 kgf-cm in ascending order to complete the installation.
- Confirm the DC supply voltage is within the 8 to 48V range before connecting; supplying more than 48V will damage the system.
- Connect the vehicle battery positive line (12V for a car, 24V for a bus/truck) to the V+ pin on the M12 S-coded DC-IN connector.
- Connect the vehicle battery negative/ground line to the GND pin.
- To enable ignition power control, connect the vehicle's ACC line to the PWR_IGN pin (Pin 4) on the M12 A-coded COM1/COM2 connector.
- In Windows, set "When I press the power button" to "Shut down" so the ignition control module correctly recognizes a completed shutdown and avoids a forced hard-off after 10 minutes.
- Wall mount: Remove the four brackets and sixteen screws from the accessory box. Secure a bracket to each of the four designated mounting locations on the enclosure using the supplied screws. Repeat on all sides of the enclosure.
- Rack mount (optional accessory): Using the kit's two brackets, two grips, and eight screws, install the larger bracket on the left side of the enclosure (next to the COM port side) with the supplied screws, then repeat on the other side.
- Optionally attach the grips to the rack-mount brackets using the M3 screws provided, matching the grip openings to the bracket.
- Back up all hard drive data before proceeding, as RAID creation may cause irreversible data loss. Use at least two drives, ideally from the same batch.
- Enter BIOS by pressing F2 at boot, then go to Advanced > SATA And RST Configuration > SATA Mode Selection and select "Intel RST Premium With Intel Optane System Acceleration."
- Go to Boot and select either Legacy Boot Type or UEFI Boot Type, then press F10 to save and reboot.
- Legacy mode: Press Ctrl+I at reboot to enter the RAID configuration utility, select "Create RAID Volume," name the volume, choose RAID Level (RAID0/RAID1), set Stripe Size (RAID0 only), set capacity, and confirm creation.
- UEFI mode: Press F3 at reboot to enter the Configuration Utility, select Intel Rapid Storage Technology > Create RAID Volume, name the volume, choose RAID Level, select disks, set Stripe Size (RAID0 only), set capacity, and select Create Volume.
- Press F10 to save and exit once the RAID volume has been created.
SEMIL-1700GC series is one of the world’s first IP67-rated, waterproof, and dustproof inference servers with pre-installed NVIDIA RTX 2000 Ada or L4 for the most demanding environments. It is a brand-new page in Neousys’ chapter of innovations as it represents a new level of robustness for rugged-edge AI solutions. Coupled with Intel Xeon E or 9th/ 8th-Gen Core CPU, the system delivers excellent CPU and GPU performances for advanced edge AI applications in various environmental settings. SEMIL-1700GC series features Neousys’ patented system architecture* to guarantee -40°C to 70°C fanless operation in a rack or wall-mountable 2U 19” enclosure.
SEMIL-1700GC series features a sophisticated thermal design to dissipate the heat generated by RTX 2000 Ada or L4 GPU to ensure maximum GPU performance in high-temperature environments. It has a corrosion-proof, stainless steel/ aluminum chassis with molded o-rings plus a patented fusion mechanism design to offer extraordinary durability and watertight construction. SEMIL-1700GC series offers a variety of I/O connectivities, including 802.3at Gigabit PoE+, VGA, USB, COM ports, and optional 10G Ethernet, all using M12 connectors for water-proof and extreme-rugged connectivity in shock and vibration conditions. Additionally, it features M.2 for NVMe SSD, 2.5” SATA storage accommodation, 8 to 48V wide-range DC input with ignition power control, and complies with MIL-STD-810G and EN 50155 EMC.
The inference acceleration of rugged GPU computers actualized real-time AI inference applications at the edge, where extremely rough conditions are expected. By combining powerful CPU/ GPU, robust IP67 protection, true fanless wide-temperature operation, rugged M12 connectors, and standard 2U 19” rack, the SEMIL-1700GC series reveals unprecedented possibilities of deploying AI to places that have yet to be reached.
| Product Available On | Aug 31, 2021 |
|---|---|
| Manufacturer | Neousys |
| Short Description | SEMIL-1700GC series is one of the world’s first IP67-rated, waterproof, and dustproof inference servers with pre-installed NVIDIA RTX 2000 Ada or L4 for the most demanding environments. It is a brand-new page in Neousys’ chapter of innovations as it represents a new level of robustness for rugged-edge AI solutions. Coupled with Intel Xeon E or 9th/ 8th-Gen Core CPU, the system delivers excellent CPU and GPU performances for advanced edge AI applications in various environmental settings. SEMIL-1700GC series features Neousys’ patented system architecture* to guarantee -40°C to 70°C fanless operation in a rack or wall-mountable 2U 19” enclosure. |
| Processor | i3, i5, i7 8th and 9th Gen, Xeon E |
| Graphics | Intel UHD Graphics 630 |
| Memory | DDR4-2400/2666MHz SDRAM two sockets |
| Chipset | Intel C246 platform controller hub |
| AMT | 12.0 |
| PoE | 4x PoE+ |
| Ethernet Standard | I213, I210 |
| Video Port | 1x VGA, 1 DP |
| Audio | 1x 3.5mm mic in/spk out |
| M.2 | 1x 2242 B key for LTE, 1x 2242 E key for WiFi, 1x 2280 M key for storage |
| Mini PCI-E | 2 |
| mSATA | 2x full mSATA internal |
| 2.5" Drive | 2x SATAIII internal |
| DC Input | 8-48V DC |
| Power Adapter | 280-480W |
| Power Input Voltage | 8-48V DC |
| Power Type | DC |
| Fan | fanless |
| Dimension | 440mm x 310mm x 86.5mm |
| Weight | 12kg |
| Mounting | rack and wall mount options |
| Operating Temperature | see specifications sheet and manual for configuration related ranges |
| Storage Temperature | -40-85C |
| Humidity | 10-90% non condensing |
| Vibration | MIL-STD810G, Method 514.7, Cat 4 |
| Shock | MIL-STD810G, Method 516.7, Procedure 1 |
| EMC | EN-50115, CE/FCC Class A |
| CPU Cores | 6, 8 |
| CPU Family | Intel Core, Intel Xeon |
| Base CPU Speed | 3.1 to 3.5 GHz, Over 3.5 GHz |
| Video Output | Display Port, VGA |
| PoE Ports | 4 |
| Serial Ports | 3-4 |
| USB 2.0 | 3-4 |
| USB 3.0 | 3-4 |
| Max Memory | 64 GB |
| Operating System | Windows 10, Linux |
| Effective Memory Speed | 2400 MHz, 2666 MHz |
| Form Factor | Fanless |
| Native Storage Type | 2.5" SSD, mSATA Full, M.2 SATA S80 |
| On/Ignition | Built In Ignition Control |